UIS Command Component Parameters
The following tables list and describe the parameters specific to the UIS command component types for this remote device:
For more general information about UIS command component parameters, see UIS Command Components. The DG_F_DEV (Get data group from device) and DG_T_DEV (Send data group to device) command component types are configured in the template file. The other command component types are considered special and are defined in the EIE editor code. See Special UIS Command Component Types for more information.
CYUPDTPT
Update CygNet Point updates the record for a CygNet point. CYUPDTPT has the following command parameters:
| Parameter | Required | Description |
|---|---|---|
|
FOnErr |
No |
Fail cmd on update error indicates to abort the UIS command if any update errors are encountered. The errors that might come up include: if the point specified in the Fac, Serv, Site, or UDC parameters does not exist, or if the point exists in a different UIS and any messaging errors or communication failure to that service comes up. |
|
Fac |
Yes |
Facility for pt identifies the facility of the point to update. |
|
Serv |
No |
Service for pt identifies the SERVICE of the point to update. |
|
Site |
No |
Site for pt identifies the SITE of the point to update. |
|
UDC |
Yes |
UDC for pt identifies the UDC of the point to update. |
|
UType |
No |
Update type indicates the type of update. Value options are 0 - 3, where 0=Completion, 1=Success, 2=Failure, 3=Creation. |
|
UsrMsk |
No |
User bit mask specifies the user bit mask of the point to update. |
|
UsrVal |
No |
User bit value to match specifies the user bit value to match when updating the point record. |
|
Value |
No |
Value indicates the point value to update. |
CYWAITPT
Wait for CygNet Point signals the UIS to wait to perform a command until the value of the specified CygNet point changes to a specified value.
CYWAITPT must be the first command component added to a UIS command. You cannot add other instances of CYWAITPT to a UIS command.
CYWAITPT has the following command parameters:
| Parameter | Required | Description |
|---|---|---|
|
Dur |
Yes |
Duration is the amount of time (in HH:MM:SS or HH:MM or HH) for the UIS command to wait for the point value to change before timing out. |
|
FOnErr |
No |
Fail on point error indicates to abort the UIS command if any error conditions are encountered. The point errors that might come up include: if the point specified in the Fac, Serv, Site, or UDC parameters does not exist, or if the point exists in a different UIS and any messaging errors or communication failure to that service comes up. |
|
Fac |
Yes |
Facility for pt identifies the facility of the point on which to wait for the point value to change before performing the UIS command. |
|
Int |
Yes |
Interval indicates the frequency (in HH:MM:SS or HH:MM or HH) with which the UIS will check the point’s value to see if it has changed. |
|
Serv |
No |
Service for pt identifies the SERVICE of the point on which to wait for the point value to change before performing the UIS command. |
|
Site |
No |
Site for pt identifies the SITE of the point on which to wait for the point value to change before performing the UIS command. |
|
UDC |
Yes |
UDC for pt identifies the UDC of the point on which to wait for the point value to change before performing the UIS command. |
|
UsrMsk |
No |
User bit mask specifies the user bit mask on which to wait for the status bit change before issuing the UIS command. Note: The user status bit parameters (UsrMsk and UsrVal) only apply to the extended status field of the point record, so they will not match anything in the base status. |
|
UsrVal |
No |
User bit value to match specifies the user bit value to match before issuing the UIS command. |
|
Value |
No |
Value to match specifies the value on which to wait for the point to change to before issuing the UIS command. Note: You can set parameters for both the point user status AND point value. So you can match either one by itself, or you can specify that both must match your parameter values. |
DG_F_DEV
Get data group from device retrieves a data group from a field device. The Parent XML Element is uccRecvParms. The following parameters are available for each specified data group type.
| Data Group Type | Parameter | Required | Description | Value Options |
|---|---|---|---|---|
|
DataType |
Yes |
Data Type defines the type of data stored at the specified register number. |
Value options appear in the Data Type drop-down list in the Single Read-Only Coil data group dialog box. |
|
|
FacUdc |
No |
Facility.UDC for Point Processing provides a means to specify a UDC to which to map the specified data point; it requires a corresponding point in the Point Service (PNT). |
Strings that specify a Facility.UDC combination. |
|
|
RegNum |
Yes |
Register Number specifies the register number used to retrieve data from a single element. |
Valid register numbers |
|
|
DataType |
Yes |
Data Type defines the type of data stored at the specified register number. |
Value options appear in the Data Type drop-down list in the Single Read-Only Register data group dialog box. |
|
|
FacUdc |
No |
Facility.UDC for Point Processing provides a means to specify a UDC to which to map the specified data point; it requires a corresponding point in the Point Service (PNT). |
Strings that specify a Facility.UDC combination. |
|
|
RegNum |
Yes |
Register Number specifies the register number used to retrieve data from a single element. |
Valid register numbers |
DG_T_DEV
Send data group to device sends a data group to a field device. The parent XML Element is uccSendParms. The following parameters are available for each specified data group type.
| Data Group Type | Parameter | Required | Description | Value Options |
|---|---|---|---|---|
|
DHStrkLen |
Yes |
Downhole stroke length |
Floating-point numbers |
|
| FldOff |
Yes |
Fluid pound offtime |
Floating-point numbers |
|
|
FldOffTim |
Yes |
Fluid pound off-timer |
Floating-point numbers |
|
|
FldPnd |
Yes |
Fluid pound cycles required |
Integers | |
|
FldStrk |
Yes |
Fluid pound strokes |
Integers | |
|
HiPressSD |
Yes |
High pressure shutdown |
Integers | |
|
IgnoreStrk |
Yes |
Startup ignore strokes |
Integers | |
|
LoadSP |
Yes |
Load setpoint |
Integers | |
|
LwPressSD |
Yes |
Low pressure shutdown |
Integers | |
|
MinLoad |
Yes |
Min load limit |
Floating-point numbers |
|
|
MnArea |
Yes |
Min area |
Floating-point numbers |
|
| MnAreaStr |
Yes |
Min area strokes |
Integers |
|
|
MnAreaTm |
Yes |
Min area timer |
Floating-point numbers |
|
|
MnOffA |
Yes |
Minimum offtime allowed |
Floating-point numbers |
|
|
MnStrkDlt |
Yes |
Minimum stroke delta |
Floating-point numbers |
|
|
MsMPRL |
Yes |
Measured MPRL |
Floating-point numbers |
|
|
MsPPRL |
Yes |
Measured PPRL |
Floating-point numbers |
|
|
MtrCorrFtr |
Yes |
Meter correction factor |
Floating-point numbers |
|
|
MxOffA |
Yes |
Maximum offtime allowed |
Floating-point numbers |
|
|
MxStrkDlt |
Yes |
Maximum stroke delta |
Floating-point numbers |
|
|
OffInc |
Yes |
Offtime increment |
Floating-point numbers |
|
|
PeakLoad |
Yes |
Max load limit |
Floating-point numbers |
|
|
PlngrDia |
Yes |
Plunger diameter |
Floating-point numbers |
|
|
PrUpDly |
Yes |
Power up delay |
Integers |
|
|
PressDly |
Yes |
Pressure startup delay |
Floating-point numbers |
|
|
RadioErr |
Yes |
Radio errors |
Integers | |
|
ResetCt |
Yes |
RTU resets |
Integers | |
|
RunTarg |
Yes |
Target runtime |
Floating-point numbers |
|
|
StrkFltCnt |
Yes |
Stroke fault counter |
Integers | |
|
StrkSP |
Yes |
Stroke setpoint |
Integers | |
|
StrokeLen |
Yes |
Stroke length |
Floating-point numbers |
|
|
UcMPRL |
Yes |
Uncalibrated MPRL |
Floating-point numbers |
|
|
UcPPRL |
Yes |
Uncalibrated PPRL |
Floating-point numbers |
|
|
ActByPass |
Yes |
Active/bypass |
Boolean |
|
|
Aux1 |
Yes |
Aux #1 presco (OK/Fault) |
Boolean |
|
|
Aux2 |
Yes |
Aux #1 pollution (OK/Fault) |
Boolean |
|
|
ClockMd |
Yes |
Time clock mode (off/on) |
Boolean |
|
|
FluidLb |
Yes |
Fluid pound status (OK/waiting) |
Boolean |
|
|
HelpMe |
Yes |
Help me (fault/normal) |
Boolean |
|
|
LoadFlt |
Yes |
Load device/cable (OK/fault) |
Boolean |
|
|
MinAreaSD |
Yes |
Min area shutdown (OK/fault) |
Boolean |
|
|
MinMaxFlt |
Yes |
Min/Max load (OK/fault) |
Boolean |
|
|
MotorCont |
Yes |
Motor contact (off/on) |
Boolean |
|
|
MotorEnb |
Yes |
Motor enable (off/on) |
Boolean |
|
|
MotorStrt |
Yes |
Motor start trigger (1=start) |
Boolean |
|
|
NoMotFlt |
Yes |
No motion (OK/fault) |
Boolean |
|
|
SDIncom |
Yes |
SD incomplete (OK/fault) |
Boolean |
|
|
SDLock |
Yes |
SD + lockout (OK/fault) |
Boolean |
|
|
SDPower |
Yes |
SD no power (OK/fault) |
Boolean |
|
|
SrokeFlt |
Yes |
Stroke device/cable (OK/fault) |
Boolean |
|
|
UPLPerm |
Yes |
UPL permissive (off/on) |
Boolean |
|
|
WarnBeac |
Yes |
Warning beacon (off/on) |
Boolean |
|
|
DataType |
Yes |
Data Type defines the type of data stored at the specified point type. |
Value options appear in the Data Type drop-down list in the Single Read/Write Coil data group dialog box. |
|
|
FacUdc |
No |
Facility.UDC for Point Processing provides a means to specify a UDC to which to map the specified data point; it requires a corresponding point in the Point Service (PNT). |
Strings that specify a Facility.UDC combination. |
|
|
RegNum |
Yes |
Register Number specifies the register number used to retrieve data from a single element. |
Valid register numbers |
|
|
Value |
Yes |
Value defines a value to be sent to a "Single Coil" (SnglCoil) data group. |
|
|
|
|
DataType |
Yes |
Data Type defines the type of data stored at the specified register number. |
Value options appear in the Data Type drop-down list in the Single Read/Write Register data group dialog box. |
|
FacUdc |
No |
Facility.UDC for Point Processing provides a means to specify a UDC to which to map the specified data point; it requires a corresponding point in the Point Service (PNT). |
Strings that specify a Facility.UDC combination. |
|
|
RegNum |
Yes |
Register Number specifies the register number used to retrieve data from a single element. |
Valid register numbers |
|
|
Value |
Yes |
Value defines a value to be sent to a "Single Register" (SnglReg) data group. |
|
|
|
|
EUpStrk |
Yes |
End of upstroke |
Floating-point numbers |
|
MnLdTgt |
Yes |
Minimum load target |
Floating-point numbers |
|
|
Mode |
Yes |
Mode number |
Integers |
|
|
PkLdTgt |
Yes |
Peak load target |
Floating-point numbers |
|
|
SDnStrk |
Yes |
Downstroke speed |
Floating-point numbers |
|
|
SUpStrk |
Yes |
Upstroke speed |
Floating-point numbers |
|
|
SpdByp |
Yes |
Speed bypass |
Floating-point numbers |
|
|
SpdDec |
Yes |
Speed decrease |
Floating-point numbers |
|
|
SpdInc |
Yes |
Speed increase |
Floating-point numbers |
|
|
SpdMax |
Yes |
Maximum Speed |
Floating-point numbers |
|
|
SpdMin |
Yes |
Minimum Speed |
Floating-point numbers |
